Welcome, Guest
Username: Password: Remember me

TOPIC: EESDR3 - TCI 1.7 - RX_SENSORS commands don't work

EESDR3 - TCI 1.7 - RX_SENSORS commands don't work 07 Apr 2022 20:00 #1

  • iw7dmh
  • iw7dmh's Avatar
  • OFFLINE
  • Posts: 250
  • Thank you received: 116
Hi,
I am wondering if the RX_SENSORS command and the other similar commands, are already implemented in the EESDR3 - TCI protocol interface.
Sending the RX_SENSORS_ENABLED:true,200; the TCI server should send the RX_SENSORS:arg1,arg2; answers at the defined interval.
Actually I receive no answer.

Can you help me?
Thank youv ery much

73' Enzo
iw7dmh
The administrator has disabled public write access.

EESDR3 - TCI 1.7 - RX_SENSORS commands don't work 07 Apr 2022 20:32 #2

  • sq3rx
  • sq3rx's Avatar
  • OFFLINE
  • Posts: 18
Hi Enzo,
I tested RX and TX Sensors with my configuration about 2 weeks ago without any success.
I think this part od TCI is still buggy or even not implemented.

73! Mel sq3rx
The administrator has disabled public write access.

EESDR3 - TCI 1.7 - RX_SENSORS commands don't work 07 Apr 2022 20:57 #3

  • iw7dmh
  • iw7dmh's Avatar
  • OFFLINE
  • Posts: 250
  • Thank you received: 116
Hi Mel,

thank you very much for the answer, this is what I need to know.

73, iw7dmh
The administrator has disabled public write access.

EESDR3 - TCI 1.7 - RX_SENSORS commands don't work 08 Apr 2022 14:51 #4

  • Rome
  • Rome's Avatar
  • OFFLINE
  • Quod Licet Jovi Non Licet Bovi
  • Posts: 1049
  • Thank you received: 528
Hello,
These commands should work, they were tested here in the office and by the developers of JTDX and SDC.

Enzo, please contact us directly via email and thoroughly explain the situation.
Роман, Roman
Expert Electronics
The administrator has disabled public write access.

EESDR3 - TCI 1.7 - RX_SENSORS commands don't work 13 Apr 2022 09:11 #5

  • iw7dmh
  • iw7dmh's Avatar
  • OFFLINE
  • Posts: 250
  • Thank you received: 116
Well,
thank to Roman's help I made my ESP32 working with the (TX/RX)_SENSOR commands.
Everything is fine in the TCI code library, but the manual has a typo on the two SENSORS commands.
The manual says RX_SENSORS_ENABLED:true,200; but the right command is RX_SENSORS_ENABLE:true,200;.
The same is for TX_SENSORS_ENABLED:true,200; vs TX_SENSORS_ENABLE:true,200;.
Just delete the D letter from the command and everything is fine.

73' Enzo
iw7dmh


rx_sensors_enable.png
The administrator has disabled public write access.
The following user(s) said Thank You: Rome

EESDR3 - TCI 1.7 - RX_SENSORS commands don't work 13 Apr 2022 15:07 #6

  • OK1AU
  • OK1AU's Avatar
  • OFFLINE
  • Posts: 7
  • Thank you received: 10
Good work Enzo.
Thanks

Stan
Last Edit: 13 Apr 2022 15:07 by OK1AU.
The administrator has disabled public write access.
Time to create page: 0.079 seconds