When trying to use the remote part in esdr3.
I set my cloud account as shown.
started the starter software on local net work sunsdr2 pro
which is connected ok

when using laptop on anther network Ie 4g network cell
i run up esdr3 go to log on to the cloud account in program , noticed on local pc where radio is connected, the starter software is closes or logs out.
also theremote pc radio does not appear in window connected radios.
if i am right the starter software should remain on all time which is part of the connection
Any ideer's

I tried to set it up too and followed all instructions and youtube videos and have exactly the same problem.

I had a quick look at the v3 remote software earlier. So created a cloud account, edited the config.json file with my credentials then started a CMD prompt on the server and ran the starter.exe program. This successfully connected. Then I firstly tried the web client. I was presented with my radio on the home page under 'select device' but when I click the connect button I get the message 'There are no available devices!'. On the server screen, I do see successful messages. 'Cell Started successful' and 'Cell close correctly'. I then tried the ExpertSDR v3 Software. From the ExpertSDRv3 launcher program, select the 3rd tab option to set up the radio.



But even though the radio appears when I click the start button from the ExpertSDRv3 launcher, the 'Power On/Start transceiver button' doesn't do anything on the radio. Again I do see the successful Cell Started/Cell close messages appearing on the server in the starter.exe command window.

I will try and debug.

Still no joy with this. The ExpertSDRv3 software just indicates that the radio isn't available. Same message received on the web client.





I ran a network & process monitor on both the client and the remote server PC. I see lots of traffic on both to/from IP address 95:174:99:52 on port 5450. No errors noted.

Hi,

the same problem with me...

Thanks for the heads up. I won't spend any more time investigating this issue. Will wait for alpha 12.

I can confirm the exact same issue.

Same issue for me, when I run server.exe it connects but when I log in to EESDR server with my credentials server.exe closes. I tried with my phone both on the LAN and WAN, same issue + tried with another laptop with V3.

So I suppose we can consider remote over internet use to be impossible for now, works fine over LAN.

One other thing, why does cell.exe have a load of 169.254 ip addresses ?

I am having the same problem, I have spent hours working on this only to have the same problem that others are having. Hope 12 has this fixed I have some people wanting to log into my Sun to see if they want to buy a Sunsdr or some other SDR radio. I guess we just have to have patience. I do love my SunSDR2DX. Best radio I have every owned.

Tom
KC4CBQ

Follow this thread it works for me now no problems.

eesdr.com/en/forum-en/remote-control/9464-starter-program-in-windows?limitstart=0

I followed Rick's video 3 times to make sure I did everything correctly and still no joy. I have turned off all firewalls and stopped all programs and anti-virus services. It all works until I get to when the program opens the power button will flash white then back gray.

I am using the SunSDR2 Dx with EESDR3 V 11 and operating remote without issue.
In fact, I'm using it right now on the 80m band.
The Transmit function is not available but operating the receiver remote is a real pleasure.

Once the Starter Pgm is setup and saved, just have the SDR turned on, do not have the ESDR3 program operating, just the Starter Pgm, which once started, will come up and state "Connect Successful".
On your remote PC Registration for the Client is set up, click on it and log in.
The next window will show the radio Logging In and showing your device.
Click on CONNECT and you will see a window showing Connection Successful, and a GO button to select.

I'm waiting for the final release of SDR3, not another Alpha version.
I wonder what the release time frame that we can expect?

GL Tom W3FRG

Hello,
We plan to release the next ESDR3 0.13.0 Betta by the end of March, it'll have TX mode in ERS.

Like many others on this thread I have problems to get remote connection working.
In the starter folder I find cell.exe. When running it, four addresses come up. One is the 192.168.0.118:5050, which is the radio.
The three others start with 169.254.... and all endring with :5050. These are addresses that I cn't find in my system.
Is this correct, or is it a bug?

I followed Ricks discription. It worked Very well. I using windows 10. BUT I can not connect to my antenna. What have I missed. I have no stations on spectrum or waterfall but I get the audio from noisefloor and also noisefloor signals in spectrum and waterfall But it seems to not connect to my antenna? Somebody have a clue?
de sm6usu Svante