Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1
  • 2

TOPIC: Where to download EESDR3 0.13.0 ?

Where to download EESDR3 0.13.0 ? 15 Aug 2022 19:06 #16

  • N8SDR
  • N8SDR's Avatar
  • OFFLINE
  • Posts: 624
  • Thank you received: 294
W3FRG wrote:
Rick,
One of the very first preliminary items I check when using the Amp is verifying the RF input Level before putting the amp into Operate.
In Remote the Power settings, Using the Power Correction table, appeared to be greyed out, dull, not bright as one would expect.
I will re check this again.
But I totally agree, it's an Alpha version and one needs to be aware and understand its limitations.

Tom W3FRG

Yes the TX power in REMOTE MODE with ERS still needs work this as i mentioned also part of upcoming firmware and core changes, just keep an eye on it!
73 Rick
The administrator has disabled public write access.

Where to download EESDR3 0.13.0 ? 15 Aug 2022 19:21 #17

  • N8SDR
  • N8SDR's Avatar
  • OFFLINE
  • Posts: 624
  • Thank you received: 294
N8SDR wrote:
cicciomessere wrote:
Hi everybody,I've just installed the 0.13 software but when I start the program it give me a msg " Lost connection with Sunsdr2dx":Anyone got the same problem?

Makes sure you have upgraded the firmware

Power off the radio completely (removing power from rear of rig) to allow it to fully reset

then try

see above post regarding firmware, also check that your AV isn't blocking the program or that a windows firewall hasn't blocked it either

I think John's issue same as yours was windows firewall related. as a test disable firewall and try it, PLEASE DONT KEEP IT DISABLED, just a test- if that works try adding exception
73 Rick
Last Edit: 15 Aug 2022 19:22 by N8SDR.
The administrator has disabled public write access.

Where to download EESDR3 0.13.0 ? 15 Aug 2022 19:40 #18

  • W3FRG
  • W3FRG's Avatar
  • OFFLINE
  • Posts: 42
  • Thank you received: 8
Rick,
Just went to back to Remote and verified that there is NO RF OUTPUT with this Ver 13 Alpha Version.
Will wait for the upgrades you mentioned.

Tom W3FRG
The administrator has disabled public write access.

Where to download EESDR3 0.13.0 ? 15 Aug 2022 19:55 #19

  • John-KC2QMA
  • John-KC2QMA's Avatar
  • OFFLINE
  • Posts: 136
  • Thank you received: 83
John-KC2QMA wrote:
I just installed the new Beta on my MB1 and updated firmware but when I open the program I get a message “MB1 Lost Connection” any suggestions to resolve the issue?
John

UPDATE: I got it working with the help of Rick.
The issue is with firewall settings. For some reason when I installed 0.13 it did not correctly open up the firewall for esdr3. I just reset my windows firewall settings then opened v0.13 alpha again and when prompted to change firewall setting make sure you check Private and Public.
Transceiver: MB1 Prime 2021
HF Amplifier: Ameritron AL-1200
HF Antennas:10-80 Vertical, 10-80 Fan Dipole
VHF Antenna: Commet GP-9
The administrator has disabled public write access.

Where to download EESDR3 0.13.0 ? 15 Aug 2022 22:51 #20

  • N8SDR
  • N8SDR's Avatar
  • OFFLINE
  • Posts: 624
  • Thank you received: 294
W3FRG wrote:
Rick,
Just went to back to Remote and verified that there is NO RF OUTPUT with this Ver 13 Alpha Version.
Will wait for the upgrades you mentioned.

Tom W3FRG

Yes, it should work in TX mode on Remote connection if you setup and use ERS (Expert Remote Systems) With exception I think the MB1 if I recall, see release note regarding copied below

Another member in Indonesia and I here in US worked with each other's rigs remotely for a test.

are you using the new ERS server, as you need to be

and also, you need on each side be using the V13 080722 version as well. Start server on side with the radio
and on the side, you're working from open V1 13 08072022 and login to your ERS account shortly after the rig will show in the available list
you can TX then, but again I will state that TX really needs to be watched as the power output can vary, you must also use the PC MIC input as well stated in the release notes.

from release notes regarding TX remote using ERS

New features in ERS:
• Implemented TX mode for ERS (CW transmission is not supported yet). Transmission with
MB1 is unstable, will be fixed in the software release version. To work in TX mode via ERS,
you should select the MicPC in the software.
• Implemented PROC module for voice operation
• Implemented control of TX modulator settings, similar to the TX tab in ExpertSDR2
73 Rick
Last Edit: 15 Aug 2022 22:56 by N8SDR.
The administrator has disabled public write access.

Where to download EESDR3 0.13.0 ? 15 Aug 2022 23:29 #21

  • W3FRG
  • W3FRG's Avatar
  • OFFLINE
  • Posts: 42
  • Thank you received: 8
Rick,

Yes, using the new Server on the rig side, created a new Starter file, and have SDR3 Ver13 Alpha on the remote end. The window comes up with both the Local and Remote selections.
The Remote comes up but the Power Correction Table is grayed out. Cannot get any RF indicated.
Have both Drive & Tune at max position.

Tom W3FRG
The administrator has disabled public write access.

Where to download EESDR3 0.13.0 ? 16 Aug 2022 00:18 #22

  • N8SDR
  • N8SDR's Avatar
  • OFFLINE
  • Posts: 624
  • Thank you received: 294
W3FRG wrote:
Rick,

Yes, using the new Server on the rig side, created a new Starter file, and have SDR3 Ver13 Alpha on the remote end. The window comes up with both the Local and Remote selections.
The Remote comes up but the Power Correction Table is grayed out. Cannot get any RF indicated.
Have both Drive & Tune at max position.

Tom W3FRG

Hello Tom

seems odd, I suggest opening a GitHub issue with it ( and this sounds like a message I hated with FRS) open a ticket. sorry

I can certainly remotely TX as long as I use the PC input mic for audio

question on the side you are remoting from, do you do a fresh install or upgrade.

Is it possible you can do an uninstall of both old and new and also clean and reg files then re install and try it. I am curious if something is left over which is causing the issue. just a suggestion to try, if possible, REVO uninstaller works well for windows at cleaning up leftovers.

Thanks for the info and updates Tom
73 Rick
The administrator has disabled public write access.

Where to download EESDR3 0.13.0 ? 16 Aug 2022 01:39 #23

  • N8SDR
  • N8SDR's Avatar
  • OFFLINE
  • Posts: 624
  • Thank you received: 294
N8SDR wrote:
W3FRG wrote:
Rick,

Yes, using the new Server on the rig side, created a new Starter file, and have SDR3 Ver13 Alpha on the remote end. The window comes up with both the Local and Remote selections.
The Remote comes up but the Power Correction Table is grayed out. Cannot get any RF indicated.
Have both Drive & Tune at max position.

Tom W3FRG

Hello Tom

seems odd, I suggest opening a GitHub issue with it ( and this sounds like a message I hated with FRS) open a ticket. sorry

I can certainly remotely TX as long as I use the PC input mic for audio

question on the side you are remoting from, do you do a fresh install or upgrade.

Is it possible you can do an uninstall of both old and new and also clean and reg files then re install and try it. I am curious if something is left over which is causing the issue. just a suggestion to try, if possible, REVO uninstaller works well for windows at cleaning up leftovers.

Thanks for the info and updates Tom

I forgot maybe this will help -I did do a video on ERS and remote TX a while back when testing this was dev version a day to 2 before the 08072022 became available however I have used it since version 08072022 and working
73 Rick
Last Edit: 16 Aug 2022 01:41 by N8SDR.
The administrator has disabled public write access.

Where to download EESDR3 0.13.0 ? 16 Aug 2022 05:34 #24

Many thanks for all your advice,,the problem was the firewall...now another strange thing,I can't see on the screen the s meter even if I have make the choice with button on the left side.May be I have to do any other setting?
The administrator has disabled public write access.

Where to download EESDR3 0.13.0 ? 16 Aug 2022 12:51 #25

  • N8SDR
  • N8SDR's Avatar
  • OFFLINE
  • Posts: 624
  • Thank you received: 294
All

Following different topics and issues under this posted topic is difficult

For the S meter issues there is already a post- eesdr.com/en/forum-en/expertsdr/9907-no-large-s-meter-on-expert-13

please follow the recommendation of posting a GitHub issue report regarding the S meter that GitHub issue tracker is listed in a replay to that topic
73 Rick
The administrator has disabled public write access.

Where to download EESDR3 0.13.0 ? 16 Aug 2022 13:27 #26

  • W3FRG
  • W3FRG's Avatar
  • OFFLINE
  • Posts: 42
  • Thank you received: 8
Rick,

I have reviewed your video and submitted a BUG report describing my remote transmit issues.
I attached my picture's.
Also, if the Starter table that's updated as you progress thru a remote operation is of use, let me know where that file is and I'll fwd. it.
I do use REVO uninstaller.
Tom W3FRG
Last Edit: 16 Aug 2022 14:16 by W3FRG. Reason: update
The administrator has disabled public write access.

Where to download EESDR3 0.13.0 ? 16 Aug 2022 21:03 #27

  • N8SDR
  • N8SDR's Avatar
  • OFFLINE
  • Posts: 624
  • Thank you received: 294
W3FRG wrote:
Rick,

I have reviewed your video and submitted a BUG report describing my remote transmit issues.
I attached my picture's.
Also, if the Starter table that's updated as you progress thru a remote operation is of use, let me know where that file is and I'll fwd. it.
I do use REVO uninstaller.
Tom W3FRG

Tom, I read your Bug Report and replied to it,
Thanks for the pictures looking at them I think I possibly found your issue, see the reply I left on the Bug report and let me know- This would also explain why the first time you did have TX power out-

Here is the link to your GitHuB issue- github.com/ExpertSDR3/ExpertSDR3-BUG-TRACKER/issues/389

Please let me know if this resolves the TX remote power problem you have.
73 Rick
Last Edit: 16 Aug 2022 21:05 by N8SDR.
The administrator has disabled public write access.

Where to download EESDR3 0.13.0 ? 24 Aug 2022 20:24 #28

  • Bigboy
  • Bigboy's Avatar
  • NOW ONLINE
  • Posts: 79
  • Thank you received: 4
Thanks Rick for the reply, but I think I'm not understanding what you meant. I am using right now on my MB1 this software version (ExpertSDR2 x64 v.1.3.1 Update 9 MB1) do I have to downgrade it to update 8??
The administrator has disabled public write access.

Where to download EESDR3 0.13.0 ? 24 Aug 2022 21:21 #29

  • N8SDR
  • N8SDR's Avatar
  • OFFLINE
  • Posts: 624
  • Thank you received: 294
Bigboy wrote:
Thanks Rick for the reply, but I think I'm not understanding what you meant. I am using right now on my MB1 this software version (ExpertSDR2 x64 v.1.3.1 Update 9 MB1) do I have to downgrade it to update 8??

I'm not sure I follow

you are asking about version V2, but this topic is regarding V3 and version 13-

If you asking to run both v3 13 and v2 yes, you will need to downgrade when you go to v2 and then upgrade for v3 13 (although someone mentioned just using the newest 78.8 and when using V2 ignore the message) I cannot confirm that works.

I WOULDDN'T RECOOMEND switching back and forth as per the firmware - down/upgrades your inviting issues at some point.

Personally, for me I haven't used v2 for a long while, but that's me, I don't even have V2 installed
73 Rick
Last Edit: 24 Aug 2022 21:23 by N8SDR.
The administrator has disabled public write access.
  • Page:
  • 1
  • 2
Time to create page: 0.087 seconds