Эксперт Электроникс - Expert Electronics

Добро пожаловать, Гость

ТЕМА: TX with MSHV (FT8)

TX not working with MSHV (FT8) 13 Сен 2022 17:47 #1

tomas
Вне сайта
Сообщений: 44
Спасибо получено: 3

Hi, totally new here with ESDR3 and this is my first attempt to run it.

Linux Mint 21 (Ubuntu 22.04)
ESDR3 v13
MSHV 2.66

Conecting ESDR3 via TCI for both rig controll and ausio.
1. PTT is working Ok
2. RX is not working at start-up in MSHV, it is not starting until I have enabled TX/PTT from MSHV, then it seems ok.
3. TX is not working. I can see that signal is looking Ok in mic on ESDR3 settings and mic level (close to 0dB) but never shows any forward power and current consumption is only PA bias-current (goes from 0.6 to 4A).

Any hints would be appreciated!

Администратор запретил публиковать записи гостям.

TX not working with MSHV (FT8) 13 Сен 2022 23:07 #2

VK6NX Вне сайта Сообщений: 245 Спасибо получено: 195	Ubuntu (currently 22.04) x64 is the only Linux distro for dev/test/prod. Mint is unsupported in ESDR3. Sure you can "tweak around" Mint yourself and make some features work. However whatever features are not working under Mint - those will not be accepted as "bugs".
	73! Pavel Useful links: Network-related common Q&A: eesdr.com/en/forum-en/other-questions/9623-network-related-common-q-a Ehternet: Auto or Manusl? eesdr.com/en/forum-en/other-questions/9950-ethernet-auto-or-manual Администратор запретил публиковать записи гостям. Спасибо сказали: N8SDR, tomas

TX not working with MSHV (FT8) 14 Сен 2022 01:20 #3

N8SDR
Вне сайта
Сообщений: 160
Спасибо получено: 137

tomas пишет:

Hi, totally new here with ESDR3 and this is my first attempt to run it.

Linux Mint 21 (Ubuntu 22.04)
ESDR3 v13
MSHV 2.66

Conecting ESDR3 via TCI for both rig controll and ausio.
1. PTT is working Ok
2. RX is not working at start-up in MSHV, it is not starting until I have enabled TX/PTT from MSHV, then it seems ok.
3. TX is not working. I can see that signal is looking Ok in mic on ESDR3 settings and mic level (close to 0dB) but never shows any forward power and current consumption is only PA bias-current (goes from 0.6 to 4A).

Any hints would be appreciated!

As Pavel mentioned- that is an unsupported version of Linux

Here are the tested versions for V3

ExpertSDR3 minimal system requirements:

ОS Windows 10 x64 or later versions, Linux Ubuntu 22.04 x64 and the latest version of macOS 11

Please do not email me and ask for help I no longer will be part of this, If I could delete /remove my profile I would do so.

Администратор запретил публиковать записи гостям.

Спасибо сказали: tomas

TX not working with MSHV (FT8) 14 Сен 2022 05:14 #4

tomas Вне сайта Сообщений: 44 Спасибо получено: 3	VK6NX пишет: Ubuntu (currently 22.04) x64 is the only Linux distro for dev/test/prod. Thanks, then I know why. I have to give it a try, but Ubuntu 22 doesn't fit my needs in other ways, doesn't support cqrlog and installing flatpaks and getting out of the "sandbox" ... Ill maybe try a dedicated pc then Thanks again guys!!
	Последнее редактирование: 14 Сен 2022 05:16 от tomas. Администратор запретил публиковать записи гостям.

TX not working with MSHV (FT8) 14 Сен 2022 05:48 #5

VK6NX Вне сайта Сообщений: 245 Спасибо получено: 195	cqrlog should be OK with 22.04. Worst case - just compile from source. Also there is linlog listed in TCI SW section - this one works on Ubuntu and Mint.
	73! Pavel Useful links: Network-related common Q&A: eesdr.com/en/forum-en/other-questions/9623-network-related-common-q-a Ehternet: Auto or Manusl? eesdr.com/en/forum-en/other-questions/9950-ethernet-auto-or-manual Администратор запретил публиковать записи гостям.

TX not working with MSHV (FT8) 27 Нояб 2022 22:09 #6

tomas Вне сайта Сообщений: 44 Спасибо получено: 3	I managed to build CQRLOG after giving it another try this weekend. Time to try v3 again Is it still MSHV that goes as FT8 client in a v3 setup?
	Последнее редактирование: 27 Нояб 2022 22:09 от tomas. Администратор запретил публиковать записи гостям.

TX not working with MSHV (FT8) 28 Нояб 2022 13:55 #7

tomas Вне сайта Сообщений: 44 Спасибо получено: 3	Ok, another go and now everything works except TX. When tuning from MSHV I can see input level on TX goes close to 0dB and Mic.1 toggles to TCI and PTT works, drive sett to ~50% but no output power/carrier. I guess it something obvious I'm missing here?
	Администратор запретил публиковать записи гостям.

TX not working with MSHV (FT8) 28 Нояб 2022 14:39 #8

tomas Вне сайта Сообщений: 44 Спасибо получено: 3	I should add that this is on version 1.0.1 Beta and firmware 86.8
	Администратор запретил публиковать записи гостям.

TX not working with MSHV (FT8) 29 Нояб 2022 11:18 #9

tomas Вне сайта Сообщений: 44 Спасибо получено: 3	I can make it work now if using USB instead of FT8 mode. Known bug?
	Администратор запретил публиковать записи гостям.

TX not working with MSHV (FT8) 01 Дек 2022 12:08 #10

tomas Вне сайта Сообщений: 44 Спасибо получено: 3	Ok, now Im finally pleased here with my setup OS Kubuntu 22 ESDR3 v1.0.1 Beta and firmware 86.8 (running DIGIU mod) JTDX v2.2.159 - 32bit Audio connected via TCI Gridtracker and CQRLOG v2.60 via UDP <-> JTDX Ill update here with my findings...
	Последнее редактирование: 01 Дек 2022 12:09 от tomas. Администратор запретил публиковать записи гостям.

TX not working with MSHV (FT8) 06 Дек 2022 21:08 #11

tomas Вне сайта Сообщений: 44 Спасибо получено: 3	One issue I have noticed is when shifting bands from ESDR3 connected to JTDX via TCI, sometimes the audio connection breaks (especially TX). I have to restart JTDX to get it working again.
	Администратор запретил публиковать записи гостям.

Connection to third-party software/devices

TX with MSHV (FT8)