Добро пожаловать, Гость
Логин: Пароль: Запомнить меня
*****PLEASE, CHECK ALL PREVIOUS TOPICS, BEFORE CREATING A NEW ONE! DUPLICATED TOPICS WILL BE DELETED!*****
  • Страница:
  • 1
  • 2

ТЕМА: ATU Firmware process

ATU Firmware process 24 Окт 2021 04:13 #1

  • BKuz
  • BKuz аватар
  • Вне сайта
  • Сообщений: 1
My EESDR software likes to pop up a screen that says ATU Firmware... Failed to write firmware and an ATU firmware process waitbox. The tuner seems to have stopped tuning.

Any guidance would be appreciated.
Вложения:
Администратор запретил публиковать записи гостям.

ATU Firmware process 27 Окт 2021 04:54 #2

  • danielwee
  • danielwee аватар
  • Вне сайта
  • Сообщений: 209
  • Спасибо получено: 29
I have the same problem. Did you get any replies on this yet? Thanks.
Администратор запретил публиковать записи гостям.

ATU Firmware process 27 Окт 2021 07:16 #3

  • mir
  • mir аватар
  • Вне сайта
  • Сообщений: 51
  • Спасибо получено: 7
I also had the same problem, how I solved this problem I don't remember anymore. I only know one thing, I'm sure you need the version EESDR3 0.9.0. At the moment this version is not available on the eesdr WEB. They are looking for bugs which will be fixed soon. Waiting is the order of the day. 73 Arturo
Администратор запретил публиковать записи гостям.

ATU Firmware process 27 Окт 2021 07:40 #4

  • danielwee
  • danielwee аватар
  • Вне сайта
  • Сообщений: 209
  • Спасибо получено: 29
Ah, okay - that's hopeful. I assume that means EESDR3 comes with a new firmware version that corrects the problem. This is hopeful. Unfortunately I just have to wait for the EESDR3 0.10.0 that is supposed to come out soon. Thanks for your answer.
Администратор запретил публиковать записи гостям.

ATU Firmware process 31 Окт 2021 02:06 #5

  • danielwee
  • danielwee аватар
  • Вне сайта
  • Сообщений: 209
  • Спасибо получено: 29
For those who are facing this same issue with the AAT-100, in my case it turned out to be the cable. The cable continuity was correct but the end-to-end cable resistance was close to 6-ohms and this seemed to be the reason for my problems (which included the ATU being intermittently detected.) The initial continuity test passed but I was not looking at the resistance. When I made a new cable with end-to-end resistance of 0.3-ohms and plugged it in, the firmware update process started up the moment I fired EESDR2 up. This went to completion without problems and the ATU is now working correctly. It is also being detected consistently unlike before.

I would like to thank Roman for his patience and help in this - as well as correctly diagnosing the issue. Love the company and I have no regrets supporting them.
Администратор запретил публиковать записи гостям.
Спасибо сказали: rwardadams, g7mns

ATU Firmware process 31 Окт 2021 08:45 #6

  • mir
  • mir аватар
  • Вне сайта
  • Сообщений: 51
  • Спасибо получено: 7
Did I understand correctly you replaced the data cable ??? Thanks for your info Arturo
Администратор запретил публиковать записи гостям.

ATU Firmware process 31 Окт 2021 10:31 #7

  • danielwee
  • danielwee аватар
  • Вне сайта
  • Сообщений: 209
  • Спасибо получено: 29
To be precise, I made my own cable to replace the provided one. The one that came with the AAT-100 was correctly wired and had continuity but the cable resistance was on the high side. I made my own with lower resistance cables and it works reliably now. I suspect that even if you got a replacement cable, that batch is marginal. You might be better off making one that you know is good. Only pins 1, 2, 3, 6, 7, 8 need to be connected. I connected the shield in parallel to pin 8 (GND).
Последнее редактирование: 31 Окт 2021 10:33 от danielwee.
Администратор запретил публиковать записи гостям.
Спасибо сказали: Rome, mir

ATU Firmware process 17 Нояб 2021 09:34 #8

  • mir
  • mir аватар
  • Вне сайта
  • Сообщений: 51
  • Спасибо получено: 7
Can I have your email address? mine can be found on qrz.com
Arturo, HB9MIR
Администратор запретил публиковать записи гостям.

ATU Firmware process 17 Нояб 2021 10:03 #9

  • danielwee
  • danielwee аватар
  • Вне сайта
  • Сообщений: 209
  • Спасибо получено: 29
Mine also on QRZ under 9V1ZV
Администратор запретил публиковать записи гостям.

ATU Firmware process 03 Март 2022 07:55 #10

  • ON3CQ
  • ON3CQ аватар
  • Вне сайта
  • Сообщений: 26
  • Спасибо получено: 5
@danielwee Can you pass on the type of cable you used brand name please.

73 Pat
Администратор запретил публиковать записи гостям.

ATU Firmware process 27 Март 2022 12:35 #11

  • W4SSB
  • W4SSB аватар
  • Вне сайта
  • Сообщений: 12
  • Спасибо получено: 3
I got my AAT-100 yesterday. The provided 3 meter control cable works fine. Resistance is around .2 ohms. My serial number is 66. Seems to tune well on all bands using V2 software. Haven’t tried on V3 yet.
Администратор запретил публиковать записи гостям.

ATU Firmware process 27 Март 2022 18:09 #12

  • danielwee
  • danielwee аватар
  • Вне сайта
  • Сообщений: 209
  • Спасибо получено: 29
I made my own cable. The provided one had too high resistance.
Администратор запретил публиковать записи гостям.

ATU Firmware process 27 Март 2022 18:33 #13

  • W4SSB
  • W4SSB аватар
  • Вне сайта
  • Сообщений: 12
  • Спасибо получено: 3
That’s interesting. Mine seemed seemed to have be made with a pretty big gauge wire.
Администратор запретил публиковать записи гостям.

ATU Firmware process 29 Март 2022 07:30 #14

  • g7mns
  • g7mns аватар
  • Вне сайта
  • Сообщений: 2
I had an early cable provided with my AAT-100 and the cable was made using SCART(audio/visual) cable and didn't work. Expert Electronics sent me an updated version and the cable was heavier, more flexible and worked immediately, I'm guessing you have the updated version.

My matcher is working great now

Regards

Andrew - G7MNS
Администратор запретил публиковать записи гостям.

ATU Firmware process 29 Апр 2022 07:47 #15

  • hari
  • hari аватар
  • Вне сайта
  • Сообщений: 26
  • Спасибо получено: 8
I do have the same issue with my ATU. When I press the Info button, I do sometimes get the ATU version, etc, but most of the time it does state that the ATU is not connected. I do not see any ATU button in ExpertSDR2 either.

What resistance value would be expected for a working cable?
Вложения:
vy 73 OE6HKE
Администратор запретил публиковать записи гостям.
  • Страница:
  • 1
  • 2
Время создания страницы: 0.117 секунд