Добро пожаловать, Гость
Логин: Пароль: Запомнить меня
*****PLEASE, CHECK ALL PREVIOUS TOPICS, BEFORE CREATING A NEW ONE! DUPLICATED TOPICS WILL BE DELETED!*****

ТЕМА: Swisslogger Latency Delays and System Drag!

Swisslogger Latency Delays and System Drag! 27 Нояб 2019 12:20 #1

  • KB3Z
  • KB3Z аватар
  • Вне сайта
  • Сообщений: 181
  • Спасибо получено: 1
I installed the latest and greatest Swisslogger last evening. The only screens I had active were the Entry Screen, Telnet View Window, 2 Bandmaps. I followed the installation instructions regarding installing as Admin and running the program as an Admin. But to my dismay, even when trying to position the bandmaps the latency delays that occurred. I had both EESDR2 and Swisslogger running at the same time. I did the Control/Alt/Delete and looked at the memory usage and processor usage. I have the most current Intel Chip that my MB1 came with and also 32GB of Memory.

The memory percentage that was used was not that great. But the % of processor usage was anywhere from 40 to 100%. Plus there were times when I was getting the message at the top of the screen saying "Not Responding". I finally removed the program. Perhaps my MB1 has another program that is operating in the background that is creating an excessive amount of drag on Swisslog. I must admit I don't have these issues when running N1MM for contest operating.

Has anyone else experienced these problems? Has anyone had the program work with no latency issues whatsoever? If so I would like to know what the settings are to get this program to work. I would hate to see the drag that would occur if I had more windows activated.

Mark Griffin, KB3Z
Администратор запретил публиковать записи гостям.

Swisslogger Latency Delays and System Drag! 27 Нояб 2019 13:14 #2

  • HB9JND
  • HB9JND аватар
  • Вне сайта
  • Сообщений: 9
  • Спасибо получено: 3
Dear Mark

Did you configure TCI for the data exchange between EESDR2 and Swisslog?

vy 73, Hubert
Администратор запретил публиковать записи гостям.

Swisslogger Latency Delays and System Drag! 27 Нояб 2019 13:38 #3

  • KB3Z
  • KB3Z аватар
  • Вне сайта
  • Сообщений: 181
  • Спасибо получено: 1
Yes, I have TCI check marked.
I have half a mind to try and configure the program using com ports and disable the TCI to see if it runs any better.
Any thoughts on that?
Thanks!
Mark
Администратор запретил публиковать записи гостям.

Swisslogger Latency Delays and System Drag! 27 Нояб 2019 16:55 #4

  • g0cgl
  • g0cgl аватар
  • Вне сайта
  • Erik EI4KF / G0CGL
  • Сообщений: 661
  • Спасибо получено: 261
Ensure that the DX Cluster you are receiving Spots from is not Reverse Beacon or one with massive Skimmer Spot output.

Try this version: www.swisslogforwindows.com/SwisslV5.exe
Save your existing exe (rename it) and over-write with this one. See if it helps. Note this exe is just for your testing, it is not an official release yet. You can revert to your original exe if necessary - settings will be retained.

Swisslog runs perfectly here with many other coexisting programs running simultaneously so it should work for you. The exe does address a problem whereby Swisslog exhibited a slowdown in the presence of a high Spot count.

Erik.
Администратор запретил публиковать записи гостям.

Swisslogger Latency Delays and System Drag! 27 Нояб 2019 17:14 #5

  • KB3Z
  • KB3Z аватар
  • Вне сайта
  • Сообщений: 181
  • Спасибо получено: 1
Erik,
I will try. You would think that seeing that they give you choices for reverse beacon that there would be some sort of note saying that this may overtax the software.
Thanks!
Mark
Администратор запретил публиковать записи гостям.

Swisslogger Latency Delays and System Drag! 28 Нояб 2019 00:41 #6

  • KB3Z
  • KB3Z аватар
  • Вне сайта
  • Сообщений: 181
  • Спасибо получено: 1
Erik,
I tried it and it seems to run faster and not use so much processor speed. I am using NC7J-1 as the telnet cw skimmer.
I tried to load in my ADIF File from N1MM that was created from last weeks contest.
Is there a secret for loading in contacts the very first time?
It asks about field assignment tables.
Is there an easy way to import contacts with doing the field assignment thing?
Please advise.
Mark Griffin, KB3Z
Администратор запретил публиковать записи гостям.

Swisslogger Latency Delays and System Drag! 28 Нояб 2019 11:41 #7

  • g0cgl
  • g0cgl аватар
  • Вне сайта
  • Erik EI4KF / G0CGL
  • Сообщений: 661
  • Спасибо получено: 261
As for field assignment, unless there is a need to map something to a Swisslog Field, they can be ignored.

Erik

.

Вложенный файл:

Имя файла: import.pdf
Размер файла: 1,348 KB
Последнее редактирование: 28 Нояб 2019 11:41 от g0cgl.
Администратор запретил публиковать записи гостям.