tnx for publishing the new sdc version(9.17) sofar working good,think the decoder is even better now.

73's

SDC has been updated to version 9.19 and, in lieu of publishing its details in the UAM and since we have this thread, here are the important points.
The download for 9.19 is at www.dropbox.com/s/nji20fdkkf7p6q5/SDC_9_setup.zip?dl=0

In this version, Yuri has solved a persistent Skimmer lock-up/crash issue. The Skimmer performance is further improved. Also there are some new settings:



Right-click on the waterfall for graphics settings.
The oval circle denotes the position of a small 'thermometer' depicting processing load. Normally green, should it go to red then it is necessary to reduce the processing speed in Global Setup.

The decode window could show strange characters. These were actually Russian and can be stopped from appearing:



Lastly, a common comment from SDC users with multiple monitors was that the decoding window (if outside the Skimmer window) could get "lost". Basic rules:
1. The decoding window, if it is outside the window of the skimmer, appears only when the skimmer is working and there is a connection via TCI. Through TCI it is determined that the receiver is working - that means the window can be displayed.
2. When the decoding window is out of sight, find it by using the SDC menu in the system tray

scdc now at v9.321 drive.google.com/file/d/0B6nvX2SQAgY5Nm5mbk1BU3M3Q2c/view

now it is at 10.14 the skimmer is working better than the afreet cwskimmer so i am vy happy with it.
10.14 is an sdc.exe only its on the last page of the sdc forum page

drive.google.com/file/d/1jkVq0kqLA7nRG4tuGPVAE6epEWq_j5Pa/view
10.20

Note that your posted link is to a version with some bugs (it's still usable). In the next day or two there will be a corrected version and a Addendum update will carry the link for it. I'll post it here for you too.
Erik.

Ok Erik thanks,in this version the skimmer and cw decoding works good and i use the telnet server to combine spots , dont use the other functions

73's hans

Hello Hans - ok no problem for you then with 10.10 and I only wanted to give a heads up in case you found some problem - the current issues are with ActiSpot and the Skimmer waterfall window scaling on some monitors depending on the font chosen. Yuri is working on it today.

Ok Eric thanks for the info for me the sdc skimmer is working better than the afreet skimmer i use eesdr 1.2rc2

SunSDR2 PRO + SDC Skimmer
Internet remote CW RX test during International Naval Contest

Did not have time to participate in the contest but had a quick look on 40m using the sdc skimmer ,it worked verry good.

Yes, nice software but there are some issues,
1. sometimes even if I am on a freq with a good CW signal that is decoded correctly, (cq <callsign> test) that callsign is not displayed on the waterfall and is not transmitted on telnet.
2. in some cases the signal is not decoded even if this one is very clear, see the movie below


3. On audio mixer, I can here only the left channel, the right channel audio level is very very low although I can register correctly both channels using Audacity.
I'm sure the next versions will fix these issues

SDC now at 10.21 - minor refinements to Skimmer decoders
www.dropbox.com/s/tfkaqf6615eo9kd/SDC_10_setup.zip?dl=0

SDC is now at 10.23 - additional protocols on the PA Tab for CAT controlled device interfacing. Download link is as per previous message.

I've noticed that when I am using SDC with the MB1 to populate the spectrum display, after an hour or so, the MB1 & the SDC Program both shut down for no apparent reason. Does anybody have any ideas what the conflict is or why this should be?
73 Ray G3XLG